December 29th, 2010 by Mike Hunter

The visual art and architecture of native Oceania, includes media such as sculpture, pottery, rock art, masks and personal decoration. In these cultures, art and architecture have often been closely connected, e.g. storehouses and meetinghouses have been decorated with elaborate carvings, and so they are presented together here.

Up until the 16th and 17th centuries when European societies arrived upon the scene, Oceanic societies maintained a number of different forms of Neolithic technology. The only exception was in the northwest of New Guinea, where the people living around Geelvink Bay (Teluk Cenderawasih) imported very small quantities of metal from the Indonesians of the Moluccas (Maluku). The technique of forging was zealously guarded, like a cult secret; some tools were traded but only in amounts too small to have made much impact on normal working conditions.

Throughout the rest of Melanesia and in Polynesia and Micronesia, the basic tool was the stone blade, which was hafted as an adze or an axe, and at times interchangeably as both. Tridacna shell was occasionally used as blades in the parts of Oceania where stone was in short supply, including Micronesia and the Solomon Islands. When obsidian was available, it was chipped into blades for use as both weapons and tools. Other working materials included bamboo and bivalve shells, which allow extremely sharp edges. Some fine cutting and engraving was done with unhafted boar tusks or with hafted shark and rodent teeth. Animal bones served as gouges, awls, and needles. All these instruments were employed in working wood, which with only rare exceptions was the main medium used throughout Oceania.

Clay was also employed, mainly for sculptures, for some small musical instruments (whistles), and for pottery in Melanesia and New Guinea. The creation of clay vessels was almost exclusively women’s work, apart from in a few small areas in New Guinea and the northern Solomons. The usual method involved spiral coiling of rolls of clay. The decorating of the pot was the work of men.

Some working of shell and turtle shell was done with simple drilling and abrading tools. The carving of stone, although obviously presenting far more difficult and time-consuming problems than wood, was employed remarkably often and occurred throughout the Pacific Islands; hammering, pecking, and polishing were the main methods. Even such a hard a material as jade was mastered by grinding with abrasives.

Paint and painting were thought to animate sculpture, often literally, in religiosymbolic terms, as paint was considered to have magical, vivifying powers. Paints were generally ochres, with some vegetable-derived pigments. Water was the typical medium, occasionally supplemented with sap. Brushes were created from the fibrous ends of chewed or frayed sticks, small feather bundles, pieces of wood, and sometimes the most elementary applicator of all, the finger. Apart from sculpture, the surfaces used for painting were rock faces, bark, and tapa (cloth made from pounded bark). Rock painting was most common in Australia, where panels of bark were also used. In Melanesia, paintings were made mainly on sago-palm leaves and sheets of tapa cloth. In Polynesia the women manufactured large amounts of tapa, which they then decorated with abstract designs using vegetable dyes. Some of the techniques they used included painting, stenciling with leaf templates, rubbing over relief-design tables, stamping, and printing with carved bamboo rollers.

The only areas where weaving was practiced were the Caroline Islands, the Polynesian outlying islands east of the Solomon Islands, a small number of the Santa Cruz Islands, parts of Vanuatu, the Saint Matthias Group (northwest of New Ireland), and several places on the northern coast of Irian Jaya. Spinning was unknown; instead of yarn or thread, strips of banana fibre were used on a simple backstrap loom. Weaving was a woman’s craft in the Caroline and Saint Matthias islands but was practiced by men elsewhere. A form of “finger weaving,” as in net making, was used by Maori women in creating textiles from flax fibres.

The architecture of the Pacific Islands was varied and occasionally large in scale. Buildings reflected the structure and preoccupations of the societies that constructed them, with considerable symbolic detail. Technically, most buildings in Oceania were no more than simple assemblages of poles held together with cane lashings; only in the Caroline Islands were complex methods of joining and pegging known.

Oceanic artists’ quest for media was completely opportunistic; they regarded almost anything from the lavish natural world that surrounded them as potentially usable. The ocean yielded shells of all kinds, particularly conus, cowrie, and nassa shells. Birds provided down, beaks, and plumes (those of the birds of paradise were particularly prized); animals provided teeth, tusks, and skins; insects supplied wonderfully brilliant wing cases. The vegetable realm was drawn upon for flowers, leaves, and fibres. The assembly of such materials into single objects was rare in Polynesia and Micronesia, but the practice was typical of Australian and Melanesian styles, and added brilliantly to their more spectacular effects. The most basic medium of all was the human body, which received both removable and permanent decorations, including scarification, enhanced by treatment to raise keloid welts in New Guinea, and tattooing with needles and pigments elsewhere.

For quality discount art supplies and artist supplies, make sure you visit discountart.com.au for your art supplies. Australia boasts some of the worlds most innovative artists and art galleries.

Ok, so you’ve just had your brand new grid-connected solar panels connected by your friendly accredited solar power installer.

Now, think back to the initial meeting you had with the sales consultant at the kitchen table. Do you recall talking about your previous energy use in the home, and what habits you could change if you decided to get solar? If you answered yes, then you probably organised your solar quote through mysolarprice.com.au, as we only engage solar companies that we are certain will educate the consumer about their typical power use and give them a better understanding of what power output the system is capable of. Some ‘fly-by-night’ solar panel companies who have only recently arrived on the scene have misled the public in the performance capacity of their grid connected systems. This has led to some mistrust and confusion in the Solar arena. Mysolarprice.com.au knows of these companies, and will not deal with the solar installers found to be giving misleading information or involved in any dishonest sales tactics.

Have you forgotten these power saving tips the solar consultant gave you? If so, don’t worry, as we have the TOP 15 tips for reducing your power consumption to get the most out of your tariff feed, whether that be Net Tariff feed or Gross Tariff feed. Some businesses with larger systems from 2kw (2 kilowatts) or more may not have to change their behaviour at all and will still be in positive territory, that is, getting a surplus or credit for their power. This depends on the home, roof type, shade, number of people in the home, appliance usage, and most importantly their behaviour in the home or in other words how they interact with their home. Some people work during the day and turn their standby power off, whilst doing their washing and household chores at night time. Whereas other people have an air-conditioned home office which uses a massive amount of power during the day and do little at night. How does this make a difference you may ask? If you are in a state like Queensland which has a “Net Tariff Feed” this is extremely important. A Net tariff feed basically means you get the balance of the power you send to the grid from the amount of power youuse during the day but not at night, because solar panels don’d generate power at night time. Therefore, if you are using a great deal of power during the day when your solar power system is working the hardest, you are competing or cancelling it out with the amount of power you are feeding back to the grid, or “Net” Feed. If however, you are not there during the day and turn off all your appliances at the wall to eliminate inactive and active standby but only leave the essential items on like the fridge, you will be streets ahead of the rest and get more of a “net” balance which can only mean one thing: more $$$$$$ in your pocket!

These top 15 energy saving tips range from modifying the building material of the dwelling, to being more energy efficient, to minor behavioural modifications like turning off the lights when you leave the room. This list is in the order of the simplest minor behaviour modifications to bigger structural changes to the building material.

TOP FIFTEEN POWER-REDUCING IDEAS

1.Turn the lights off when you vacate a room. This is especially important if you have energy-guzzling old-fashioned incandescent lights or worse, halogen lights. I have seen people leave on 4 x tastic 500w heat lamps on in the bathroom all day. That’s an incredible 2KW or 2000 watts of power being consumed for no reason.

2.Allow natural light into the rooms. This will reduce the need for lights during the day.

3.Replace all incandescent light bulbs and halogens with CFL’s (Compact Fluorescent Lamps) or LED’s. They use only approx. a quarter or less power than the standard 75watt incandescent or 60watt halogen, and can last much longer than the standard incandescents or halogens.

4.Use Sensor CFL spotlights for outdoors, instead of the old energy-inefficient spotlights of yesterday.

5.Turn off all standby power. This is probably the best tip I can give you for reducing your daily electricity consumption. A typical house generally operates at around 10-15% standby power, so if you have a quarterly bill of $400 that means $40-$60 of that account is standby power -which does nothing! It may not sound like much but that’s around $120-$240 a year just for not turning appliances off at the wall. An easy way to monitor your standby is to buy a proper standby power board.

6.Choose energy-efficient appliances. This doesn’t necessarily mean throwing out your 5-year-old fridge because it only has 2 stars, and spending $2,500 on one that is 4 star. It means if you are presented with an option of buying a new appliance, then make sure it has the highest star rating available. So if you have the money and the choice is over a 2 star 50 inch plasma TV or a 5 star 50 inch Led TV you should get the LED.

7.Turn off any second or third fridges not in use. I have found in energy audits that a lot of people have a spare chest freezer or 20-year-old rusting fridge with splitting seals in a hot garage. This will account for a great chunk of the electricity bill. Often I’ve opened the door and there’s nothing even in there, so the fridge is running -and working overtime- for no reason.

8.Turn off the computer screens and speakers when not being used. This is so easy, however most people I come across forget to do this. If you have a Sub-Woofer with a separate power supply be sure to turn that off also when not in use.

9.Draft Sealing in Winter. If you use electric heating in winter, then be sure to stop any drafts, otherwise you are definitely wasting money.

10.Use ceiling fans or pedestal fans instead of air-conditioning. Air-conditioning can be one of the most expensive appliances to use in summer. If are going to use air-conditioning in summer, make sure that the room is properly sealed, the windows are covered and you have insulation in the ceiling.

11.Air-Conditioning Tips for Summer.

- Buy the correct sized air-con for your room -not house, unless it’s ducted. If buying ducted make sure it can be zoned.
- Buy an energy efficient inverter air-conditioner with a high star rating for both cooling and heating.
- Set the thermostat between 18-21 degrees. Every degree celsius higher that you set the a/c increases its usage by 10%
- Re-circulate cool air from within instead of drawing hot air from outside. If the compressor is outside be sure its not sitting exposed in the western sun.
- Make sure the windows have both internal and external shading.

12.Air-Conditioning Tips for Winter.

- Set the thermostat to 23-26 degrees
- Wear warmer clothes to insulate your body so you need less mechanical heating
- Insulate your space as with Air-Conditioning in Summer Tips.
- Because hot air rises, a ceiling fan can be turned to the lowest setting -in reverse- as this actually pushes the warm air down towards the home’s occupants
- Avoid electric radiator heaters and electric fan heaters as they are massively expensive.
You are better to use reverse cycle air conditioning as it’s a great deal cheaper (most people don’t know this).

13.Insulation. Reflective foil type insulation is better in sub-tropical climates such as Brisbane has, whereas thicker, bulky insulation such as wool/fibreglass or polyester is best suited to the more temperate climates such as Toowoomba.

14.Windows. There are plenty of things you can do to insulate your windows to stop the heat entering the home during summer, and keep it in during winter. In summer it’s important to keep direct sun rays off the east and west windows by vertical screening, and keep it off north facing windows with big eaves or horizontal shading. This is so you can let the sun in in winter when it is lower in the sky. These are principles known as solar passive design.

15.Hot Water. If your home has an electric hot water system and you have it on the wrong tariff this can be the bulk of your bill. Generally, your hot water should be on an off-peak tariff depending on your location and retail provider. The hot water bill is normally a quarter of your electricity bill if the system is electric. If it is a relatively new heat pump it will be much less. The most efficient water heating device is Solar Hot Water, with a natural gas boost.

These are just some of the basic energy-saving tips that I have come across while performing household energy audits which I find a lot of people need help with. If you can reduce the daily consumption it’s going to make it a lot easier to:
1. Keep your bills down, and
2. Make it easier for the Solar Panels to work and provide you with a bonus or credit on your next bill.

One other thing I have yet to mention is panel care. Your panels should be kept free of dirt and grime, because even dust on the panels can drastically reduce the panel’s performance by up to 30% or more. I will look at the process of solar panel maintenance in my next article.

If you require any further energy saving tips or solar power saving tips, then Mysolarprice.com.au can help. We provide all the solar panel infomation necessary to make a well-informed solar purchasing decision.

Mysolarprice.com.au specialise in solar power brisbane solar hot water brisbane and solar pool heating brisbane

December 22nd, 2010 by Mike Hunter

The iPhone contains several applications available for it and more are being made and applied to the application store all the time. Almost anybody can invent an application for the iPhone and put it in the app store; all that one is required to do is present the app to Apple for screening and approval.

One practical application would be the red laser that comes available with the Apple iPhone. The red laser lets consumers to scan an item and immediately see the available prices of that specific item online. Along with the online comparison shopping which the barcode scanner provides, the red laser also has several other quite useful features. For instance, you can scan a movie noticed while walking around a shopping mall and the red laser will locate a copy of it online and will also provide for you to have the entire film sent to your TiVo.

The red laser is also able to add items to your shopping list. For example, when a person is about to throw away their razor, they can scan the item and it will be added on the shopping list so as to remind them to stock up on it next grocery shopping trip.

One can use the red laser to scan almost anything and get information that is relevant to their interests. You can use it on a book and the red laser will be able to find a copy of it within a nearby library. It is capable of this because of its highly developed integration with the world’s largest library catalogue -WorldCat. The red laser is also able to look for a copy of any book scanned and locate any online retailers which hold it in stock.

In addition to discovering prices and locating products, the red laser will also allow you to scan food. If someone is allergic to an ingredient, one can scan a food item and then tap on the allergen info. Instead of labouring to look through the entire list of ingredients in the packaging, red laser will reveal a list of all the ingredients within the food and show you the most common allergens within it. On top of all that, red laser can also help you eat healthier by showing you the full nutritive contents within the food.

Red Laser has several other helpful features and you may be surprised at the number of items you can scan and find useful information on. This is most definitely an application worth buying.

If you are looking for a great provider of architectural rendering services, annual report design or web design. Brisbane businesses can contact bydaughters for a free quote and expert advice.

If you ask anyone who knows about stone cladding, they’re likely to tell you one thing over anything else: it’s the bee’s knees. Really, a stack of rocks and stone never looked so good. If you’re looking at building your own dream home, you’ll want to consider including stone cladding in the final design of your house.

Far from appearing like your typical bunch of rocks stacked on top of each other, the majority of constructions that use stone cladding can look very aesthetically pleasing, not to mention reliable and very easy to construct. Stacked stone examples exist far and wide and can be found in a multitude of places. Take for example a certain country retreat in the Daylesford Hills in Victoria, where they opted to use stacked stone instead of the usual sandstone walling. The architect chose Craft Stone European Castle Stone Golden Sand as the alternative.

The result of this was a much more pleasant design and they avoided additional footings, by using timber frame & fibre cement as a substrate. This was done for use in an outdoor portion - a rock wall if you will - so it’s something that will easily catch the attention of people passing by .

But of course, usage is in no way limited for outdoor parts of a house. Indoor use is also popular, and when it comes to cases like these, its benefits can be experienced in all manner of ways, whether it ends up in the kitchen or in the rumpus room.

A stacked stone fireplace is an architectural marvel, where a timber frame clad with fibre cement sheet can be used to make. A 12mm Standard mortar joint can be used to fit the Craft Stone Stacked Ledgestone Merlot for the construction. The best part is the whole thing takes one day to construct which brings to light the amazing cost and labor saving incentives that this could potentially bring to the table. It’s obvious - less construction time means less construction worker costs, and fewer expenses in general.

With clear benefits such as those mentioned above, it’s no wonder that this method is becoming more and more popular. Add the fact that resulting designs can go well with just about anything, and suddenly it’s not so hard to understand why people say it’s the perfect design feature. Stone cladding is what dream homes are made of!

For more information about stone cladding, stacked stone and rock wall building options, please contact Craftstone Australia.

Lighting is a very important part of any room. It takes a lot of effort and research to choose the right night lights, as it can make or break a room. Decorative lights can easily liven up a room, irregardless of how drab the furniture is. Lighting also plays an essential in creating the ambience in a room. Where you place these lights should also be well-thought of, as wrong placement can ruin the mood in a room.

Interior design has greatly changed throughout the years, as decorative pieces and furniture have come to employ a more contemporary feel to them. With the development of interior design trends came the similar evolution of lighting. Designer night lights are now one of the most crucial aspects of any interior design project. Choosing decorative lights that create a statement fulfills both the aesthetic and functional sides of the designing process. Whether you want classic designs or modern ones, there is definitely a lighting piece that will suit your needs and preferences.

The addition a lampshade or two in a bedroom can make a huge difference. Drop lights are also nice additions to the living room and the dining room and string lights are increasingly becoming a necessity when decorating. There are so many different designs for night lights these days that it can be quite overwhelming to make an informed decision. Decorative lights provide an attractive feel to the room and depending on the kind of light you decide to use, it can set the overall theme of the room. More contemporary designs include LED colour change lights, large drop lights and metallic lighting fixtures. irregardless of what your desired theme is, you can find a lighting fixture that will complement it. This even extends to the garden and pond with outdoor lighting.

A lot of the modern lights today are also more cost-efficient they don’t consume too much electricity as they used to. It is ideal to choose one central light and add several accent lights so that you can dim the lighting in the room should you meed to. Warm lighting can greatly influence the ambience in the room, as it is a lot more pleasing to the eye than white lights.

Chandeliers have also greatly evolved through the years. From elaborate tear drop chandeliers, they now come in a variety of varying designs and colours. Dark wrought iron chandeliers offer more simplistic options for homes, as they are not as ornamental as traditional chandeliers but can be just as beautiful in design and lighting. Decorative night lights are most certainly a wonderful investment, as they can improve the aesthetic element of any home.

December 3rd, 2010 by Mike Hunter

Because packaging helps to regulate the immediate environment of a food product, it is beneficial in creating conditions that increase the storage life of a food. Packaging materials commonly used for foods may be classed as flexible (paper, thin laminates, and plastic film), semi-rigid (aluminum foil, laminates, paperboard, and thermoformed plastic), and rigid (metal, glass, and thick plastic). Plastic materials are widely used in food packaging because they are relatively inexpensive, lightweight, and easy to form into desired shapes.

The selective permeability of polymer-based materials to gases, for example carbon dioxide and oxygen, as well as sunlight and moisture, has led to the invention of modified-atmosphere packaging. If the barrier materials are carefully selected, a packaging material can continue a modified atmosphere inside the package and thus extend the shelf life of the food product.

Dehydrated foods must be kept apart from moisture during storage. Packaging materials such as polyvinyl chloride, polyvinylidene chloride, and polypropylene offer low moisture permeability. Similarly, packaging materials with low gas permeability are utilized for fatty foods in order to minimize oxidation. Because fresh fruits and vegetables respire, they need packaging materials, such as polyethylene, that have high permeability to gases.

Smart packages use properties that meet the special requirements of certain consumables. For example, packages made with oxygen-absorbing chemicals remove oxygen from the inside of the package, thus protecting oxygen-sensitive products from oxidation. Temperature-sensitive films display an immediate change in gas permeability when they are subjected to a temperature above or below a set constant. These films morph from a crystalline structure to an amorphous structure at a set temperature, causing the gas permeability to change substantially.

If you are looking for shrink packaging film and shrink wrap equipment, talk to Redblade. Redblade are the experts in plastic packaging and Cryrovac film.